Design of Roof Purlins - Structville (2024)

Roof purlins are members used to directly support roof sheeting materials, and could be made of timber or steel. In timber construction, purlins are nailed to the rafter or supporting trusses, while in steel roof construction, they are welded or bolted to the rafters or trusses by the means of cleats. As structural members, they resist loads, and provide lateral restraints for truss members, therefore it is important to design them properly against forces such as bending, shear, torsion, buckling etc.

In their design life, purlins are subjected to dead load (e.g self weight of sheeting materials and accessories), live load (e.g. during maintenance services and repairs), and environmental loads (e.g. wind and snow load). Therefore, a purlin should be adequately strong to withstand the loads it will encounter during its design life, and should not sag in an obvious manner thereby giving the roof sheeting an undulating and/or unpleasant appearance. This article will be focusing on design of steel purlin using cold formed sections.

Arrangement of Roof Purlins

By default, purlin sections assume the slope of the roof they are supporting. The spacing of roof purlins on rafters usually calls for careful arrangement, in the sense that it should follow the nodal pattern of the supporting trusses. By implication, purlins should ideally be placed at the nodes of trusses and not on the members themselves so as not to induce secondary bending and shear forces in the members of the truss. Furthermore, if manual analysis is employed to analyse a truss loaded in such a manner, such secondary stresses may not be captured especially if nominally pinned connections are assumed.

Cold formed Z (Zed) and C (channel) sections are normally specified for roof purlins in steel structures (see their form in image below).

Design of Roof Purlins - Structville (1)

When compared with thicker hot-rolled sections, cold-formed sections normally offer the advantages of lightness, high strength and stiffness, easy fabrication and installations, easy packaging and transportation etc. The connection of purlins can be sleeved or butted depending on the construction method adopted.

Design of Roof Purlins - Structville (2)

In terms of arrangement of roof purlins, we can have single spans with staggered sleeved/butt arrangement, single/double span with staggered sleeve arrangement, double span butt joint system, and single span butt joint system. The choice of the arrangement to be adopted can depend on the supply length of the sections as readily available in the market, the need to avoid wasteful offcuts, the loading and span of the roof, the arrangement of the rafters etc.

Therefore the roof designer must plan from start to finish. However, single and double span butt joint system are the most popular in Nigeria, due to their simplicity, and the culture of adopting shorter roof spans in the country. However, they are less structurally efficient than sleeved connections.

Design Example of Roof Purlins

We are to provide a suitable cold formed channel section for the purlin of the roof arrangement shown below.

Design of Roof Purlins - Structville (3)

Partial Factor for loads (BS EN 1990 NA 2.2.3.2 Table NA.A1.2(B))
Permanent action γG = 1.35 (unfavourable)
Variable action γG = 1.5
Combination factor for Roofs, ψ0 = 0.7
Wind loads, ψ0 = 0.5
Reduction factor ξ = 0.925

Initial Sizing of Sections
The maximum spacing of the trusses is at 3000 mm c/c
Limiting the deflection to L/200;
For continuous purlins, minimum depth of section (preliminary guide) = L/45
3000/45 = 66.667
Minimum width = 0.5L/60 = (3000/2)/60 = 25
Try C120-15 section (C – purlin) (Section picked from Albion Technical Manual, 2010).

Section Properties
In the design of purlins using EN 1993-1-3:2006, we normally utilise the effective section properties. This calculation of effective section properties can be very tedious and prone to error, hence it is very advisable to obtain information from the manufacturer’s details or you can write a program using Microsoft Excel or MATLAB for such calculations. However, we are going to make a sample calculation for the section that we are considering.

Design of Roof Purlins - Structville (4)

Thickness (tnom) = 1.5 mm
Depth = 120mm;
Flange width = 50 mm;
Lips/Edge Fold = 15 mm;
Steel core thickness (t) = 1.5 – 0.05 = 1.45 mm (Note that EN 1993-1-3:2006 recommends a thickness of 0.04 mm for zinc coated sections, but we are using 0.05 mm here)
Unit weight = 2.8 kg/m2;
Web height hp = h – tnom = 120 – 1.5 = 118.5 mm
Width of flange in tension = Width of flange in compression bp1 = bp2 = b – tnom = 50 – 1.5 = 48.5 mm
Width of edge fold cp = C – tnom/2 = 15 – 1.5/2 = 14.25 mm

Checking of geometrical proportions
b/t ≤ 60 b1/t = 48.5/1.45 = 33.448 < 60 – OK
c/t ≤ 50 c/t = 15/1.45 = 10.344 < 50 – OK
h/t ≤ 500 c/t = 120/1.45 = 82.758 < 500 – OK
0.2 ≤ c/b ≤ 0.6 c/b1 = 15/48.5 = 0.309 – OK

The effect of rounding corners due to root radius has been neglected in this design.

Gross section properties
Abr = t(2cp + bp1 + bp2 + hp) = 1.45[(2 × 14.25) + 48.5 + 48.5 + 118.5)] = 353.8 mm2

Position of the neutral axis with respect to the flange in compression;

Design of Roof Purlins - Structville (5)

Zb1 = 1.45[14.25(118.5 – 7.125) + (48.5 × 118.5) + 118.52/2 + 14.252/2] / 353.8 = 59.253mm

Effective section properties of the flange and lip in compression (clause 3.7.2)
Effective width of the compressed flange;
The stress ratio ψ = 1.0 (uniform compression)
kσ = 4 for internal compression element (clause 3.7.2 Table 3.5)

ε = √(235/fyb) = √(235/350) = 0.819

Design of Roof Purlins - Structville (6)

The effective width is;
beff = ρbb1 = 0.966 × 48.5 = 46.851 mm
be1 = be2 = 0.5beff = 0.5 × 46.851 = 23.4255 mm

Effective Width of the edge fold (lip) Clause 3.7.3.2.2 Equation 3.47
The buckling factor is;

Design of Roof Purlins - Structville (7)

cp⁄ bp1= 14.25/48.5 = 0.2938 < 0.35
So kσ = 0.5

Design of Roof Purlins - Structville (8)

Therefore since 1.149 < 1.0, take reduction factor as 1.0

The effective width is therefore ceff = ρcp = 1.0 × 14.25 = 14.25mm

The effective area of the edge stiffener;
As = t(be2 + ceff) = 1.45 (23.4255 + 14.25) = 54.629 mm2

We now have to use the initial effective cross-section of the stiffener to determine the reduction factor, allowing for the effects of the continuous spring restraint.
The elastic critical buckling stress for the edge stiffener is;

Design of Roof Purlins - Structville (9)

Where K is the spring stiffness per unit length;

Design of Roof Purlins - Structville (10)

b1 is the distance of the web to the centre of the effective area of the stiffener in compression flange (upper flange);

Design of Roof Purlins - Structville (11)

kf = 0 for bending about the y-y axis

Therefore;

Design of Roof Purlins - Structville (12)

= 175882.211 × 0.00000491305 = 0.8641 N/mm

Design of Roof Purlins - Structville (13)
Design of Roof Purlins - Structville (14)

So the elastic critical buckling stress for the edge stiffener is;

σcr,s = (2√(0.8641 × 210000 × 1007.801))/(54.629 ) = 495.901 N/mm2

The relative slenderness factor for the edge stiffener;

Design of Roof Purlins - Structville (15)

In our own case;
χd = 1.47 – 0.723(0.840)= 0.862

As the reduction factor for buckling is less than 1.0, we can optionally iterate to refine the value of the reduction factor for buckling of the stiffeners according to clause 5.5.3.2(3). But we are not iterating in this post.

Therefore;
χd = 0.862
be2 = 23.4255 mm
ceff = 14.25mm

Design of Roof Purlins - Structville (16)
Design of Roof Purlins - Structville (17)
Design of Roof Purlins - Structville (18)

The buckling factor kσ = 7.81 – 6.29ψ + 9.78ψ2
kσ = 7.81 – 6.29(-0.9346) + 9.78(-0.9346)2 = 22.231

Design of Roof Purlins - Structville (19)

Therefore, take ρ as 1.0 since 1.137 > 1.0.

Therefore, the effective width of the zone in compression of the web is;
heff = ρhc = 1.0 × 61.252 = 61.252mm

Near the flange in compression;
he1 = 0.4heff = 0.4(61.252) = 24.5mm
he2 = 0.6heff = 0.6(61.252) = 36.7512mm

The effective width of the web is;
Near the flange in compression;
h1 = he2 = 24.5mm

Near the flange in tension;
h2 = hp – (hc – he2) = 118.5 – (61.252 – 36.7512) = 93.992mm

Effective section properties;

Design of Roof Purlins - Structville (20)

Aeff = 1.45 × [14.25 + 48.5 + 24.5 + 93.992 + 23.4255 + (23.4255 + 14.25) 0.862]
Aeff = 343.858 mm2

Position of the neutral axis with regard to the flange in compression;

Design of Roof Purlins - Structville (21)

zc = 1.45[(14.25 × 111.375) + (48.5 × 118.5) + (93.992 × 71.504) + 300.125 + 87.5199] / 343.858 = 60.903 mm

Position of the neutral axis with regard to the flange in tension;
Zt = hp – Zc

Second moment of area:

Design of Roof Purlins - Structville (22)
Design of Roof Purlins - Structville (23)


Effective section modulus;
With regard to the flange in compression;
Weff,y,c = Ieff,y/zc = (777557.517) / 60.903 = 12767 mm3

With regard to the flange in tension;
Weff,y,t = Ieff,y/zt = (777557.517) / 57.697 = 13476 mm3


At a spacing of 1.2m, = 0.169 kN/m2 × 1.2m = 0.2028 kN/m
Self weight of purlin = 2.8 kg/m = 0.0275 kN/m

Total Gk = 0.2028 KN/m + 0.0275 KN/m = 0.230 kN/m

Live load
For a roof with 20° slope and no access except for normal repairs and maintenance, let us adopt a live load of 0.75 kN/m2
At a spacing of 1.2m, Qk = 0.75 kN/m2 × 1.2m = 0.9 kN/m

Wind Load
Taking a dynamic wind pressure of 1.5 kN/m2
When the wind is blowing from right to left, the resultant pressure coefficient on a windward slope with positive internal pressure is;
cpe = −0.90 upwards

Therefore the external wind pressure normal to the roof is;
pe = qpcpe = 1.5 × − 0.90 = −1.35 kN/m2
The vertical component of the wind pressure is;
pev = pecosθ = −1.35 × cos 20° = −1.268 kN/m2 acting upwards.
At a spacing of 1.2m;
Wk = −1.268 kN/m2 × 1.2m = 1.522 kN/m

STATIC SYSTEMS
We are adopting two possible systems that will offer us continuous and single span systems. The 6m span is based on supply length.

Static Model 1

Design of Roof Purlins - Structville (24)

Static Model 2

Design of Roof Purlins - Structville (25)

Load Case 1
When Dead load and live load are acting alone;
q = 1.35Gk + 1.5Qk = 1.35(0.230) + 1.5(0.9) = 1.6605 kN/m

Model 1

Design of Roof Purlins - Structville (26)
Design of Roof Purlins - Structville (27)

Load Case 2
When Dead load, live load and wind load are acting together;
q = 1.35Gk + 1.5Qk + 0.9Wk
Where the live load is the leading variable action
q = 1.35(0.230) + 1.5(0.9) – 0.9 (1.522) = 0.2907 kN/m

Model 1

Design of Roof Purlins - Structville (28)

Model 2

Design of Roof Purlins - Structville (29)

Load Case 3
When Dead load and wind load are acting alone;
q = 1.0Gk – 1.5Wk
Where dead load is favourable
q = 1.0(0.230) – 1.5(1.522) = -2.053 kN/m

Model 1

Design of Roof Purlins - Structville (30)

Model 2

Design of Roof Purlins - Structville (31)

Maximum span design moment MEd = 2.31 kNm
Maximum shear force VEd = 3.85 kN

Verification of Bending
Design moment resistance
MC,Rd = Weff,y.Fy / γm0 [Clause 6.1.4.1(1) of EN 1993-1-3:2006]

From our calculations;
Weff,y = min(Weff,y,c , Weff,y,t) = 12767 mm3

Therefore;
MC,Rd = Weff,y.Fym0 = [(12767 mm3) × (350) × 10-6] / 1.0 = 4.46845 KNm

Check of span and single support;
MEd/MC,Rd = 2.31/4.46845 = 0.5169 < 1.0 OK!

Check of shear resistance at ULS
The design shear resistance is given by;

Design of Roof Purlins - Structville (32)


Vb,Rd = (hw/sinφ.t.fbv) / γM0 (Clause 6.1.5)

The shear buckling strength (fbv) which is based on the relative web slenderness can be obtained from the table below (Table 6.1 of EN 1993-1-3).

Design of Roof Purlins - Structville (33)

Where λw ̅ is the relative slenderness for webs without longitudinal stiffeners.

Design of Roof Purlins - Structville (34)

Since 1.154 < 0.83 but less than 1.40;

fbv = 0.48fyb = 0.48 × 350 = 168 N/mm2

Vb,Rd = [(118.5 / sin90°) × 1.45 × 168] / 1.0 = 28866.6 N = 28.867 KN

Check for shear (using maximum shear force);
VEd / Vb,Rd = (3.85)/(28.867) = 0.1333 < 1.0 Shear is ok

Deflection Check
Maximum deflection under SLS (1.0gk+ 1.0qk) = 0.07 mm
Limiting deflection = L/200 = 3000/200 = 15 mm
Since 0.07 < 15mm, deflection is Ok!

Therefore, the channel Z120-15 section is adequate for the applied load.

Design of Roof Purlins - Structville (2024)
Top Articles
Latest Posts
Article information

Author: Pres. Carey Rath

Last Updated:

Views: 6298

Rating: 4 / 5 (61 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Pres. Carey Rath

Birthday: 1997-03-06

Address: 14955 Ledner Trail, East Rodrickfort, NE 85127-8369

Phone: +18682428114917

Job: National Technology Representative

Hobby: Sand art, Drama, Web surfing, Cycling, Brazilian jiu-jitsu, Leather crafting, Creative writing

Introduction: My name is Pres. Carey Rath, I am a faithful, funny, vast, joyous, lively, brave, glamorous person who loves writing and wants to share my knowledge and understanding with you.